|
|
 |
|
|
Your own rc helicopter at home by ying smith
|
|
|
Your own rc helicopter at home |
|
|
|
|
|
Entertainment
|
|
|
In order to build your own rc helicopter, or any part, you need specific materials. Make sure you make it of a sturdy element like a wooden box. You can find timber boxes of various sizes and suitable for this task. We just have to be careful that this well sealed. In my case I got a 38cm long by 29cm wide by 15 high. Around the inside perimeter glue the wood stick with a strip of ¾-inch pine to hold the top of our machine. In the same timber that I bought the box, I sold a kind of plywood with holes, about 30x40 cm sufficient to allow an extra few inches of the box. Before putting the rc helicopter lid with holes, you have to make a hole in one side of the box; the hole should be large enough so that it locks the height of our aspirations. This timber must be performed to make holes; this will allow fastening the top of the box with screws. Then, you must build two frames, to hold a sheet of high impact, which will shape our cowl, cabin or decoration of our model. The rc helicopter frame is made in ¾ pine bar and barely larger than the perforated lid. We must take into account the extent of the frame cannot be too large if not, we enter into the oven, and we cannot soften the picture. The two frames holding sheets through bolts and a butterfly to make it easier to remove and put the leaves. Once you have everything ready it's time to try it! Holding a sheet of high impact i.e., 0.5 mm between the two frames, then tighten all butterflies, turn the oven, we make an average temperature, we introduce the framework, we leave the door open to see that nothing catches fire !. We will see that the material starts to stretch, re-enter and re-stretch, that's the point we seek to make our piece. While leaving the rc helicopter frame in the oven, connect the vacuum to the opening of the box, turn on the vacuum, put the matrix on the lid with holes, and a pair of gloves in a fast cooking remove from oven the framework, we match the frame with the top of the box, and as they are covering the holes, it begins to copy itself to the sheet of high impact form of the matrix. A few seconds after the sheet is cooled can be separated from the mold.
Related Articles -
rc, helicopter,
|
Rate This Article  |
|
|
|
|
|
Do you Agree or Disagree? Have a Comment? POST IT!
| Reader Opinions |
|
|
|
|
|
|
|
|
|
| Author Login |
|
|
 |
Advertiser Login
ADVERTISE HERE NOW!
Limited Time $60 Offer!
90 Days-1.5 Million Views
|
|
TIM FAY
After 60-plus years of living, I am just trying to pass down some of the information that I have lea...more
|
|
|
|
|
PAUL PHILIPS
For more articles, blog messages & videos and a free e-book download go to www.NewParadigm.ws your p...more
|
|
|
|
|
GENE MYERS
Author of four books and two screenplays; frequent magazine contributor. I have four other books "in...more
|
|
|
|
|
LAURA JEEVES
At LeadGenerators, we specialise in content-led Online Marketing Strategies for our clients in the t...more
|
|
|
|
|
ALEX BELSEY
I am the editor of QUAY Magazine, a B2B publication based in the South West of the UK. I am also the...more
|
|
|
|
|
DONNIE LEWIS
I'm an avid consumer of a smoothie a day living, herbs, vitamins and daily dose of exercise. I'm 60...more
|
|
|
|
|
SUSAN FRIESEN
Located in the lower mainland of B.C., Susan Friesen is a visionary brand strategist, entrepreneur, ...more
|
|
|
|
|
ADRIAN JOELE
I have been involved in nutrition and weight management for over 12 years and I like to share my kn...more
|
|
|
|
|
STEPHEN BYE
Steve Bye is currently a fiction writer, who published his first novel, ‘Looking Forward Through the...more
|
|
|
|
