JBB50-B-type Binding Machine with a new package of the reciprocating machine, the machine operation and adjust the more convenient alternative to traditional wire level is set process for Binding Books, magazines, picture books and notebooks ideal binding equipment and other products. However, as with other machines, machine during use, there will be the fault phenomena of different situations, then, how fast and accurate troubleshooting is a topic worth exploring the printing business.
Print Network HC JBB50-B-type Binding Machine with Is a new package of the reciprocating machine, the machine operation and adjustments more convenient, is an alternative to traditional wire level set technique for perfect binding books, magazines, picture books and notebooks ideal for products such as binding equipment. However, as with other machines, machine during use, there will be the fault phenomena of different situations, then, how fast and accurate troubleshooting, is Print Worth of business topics.
Our company has a platform JBB50? B-type Binding package the machine, perfect binding books in the production process, the sudden appearance of such a failure phenomenon: the book caught in the pack during the run slow sometimes appear phenomenon, the emergence of this failure, on the one hand through thick, glue the back overflow of glue in there, on the other hand the book to package hot melt on the core of this, because in a state of semi-curing adhesive affect the quality of this package . The fault appears, at first concerned by inspection, analysis, still difficult to accurately determine the nature of the fault. Therefore suspected to be electrical control problem for an electrician to check the rule, electrician in check Inverter Did not find any problems, and no other wiring head found loosening, check the fuse does not burn signs rectifier is hard about contactor problem was suspected, the replacement of a new contactor, the fault still exists. Then, they suspect may be close to the switch in question, they would mail a link to a new factory close to switch replaced, the result was not ruled out the failure phenomenon. Thus, electrician in no way the case, also proposed is a mechanical issue. The officers suspected the main motor of the "vice moving Wheel device" idea may have under the card block, and remove the main motor corresponds to the "vice moving Wheel device" to check the test results are normal. Around the fault in the mechanical or electrical problem in the end find it difficult to precisely define the circumstances, the author through the PAA observation and analysis, when the machine caught the book with a single run and photo-electric control operation, it appears intermittent, there is no rule book folder to run slower, whereas with continuous automatic operation, the book is no slower clip phenomenon. Obviously, when the book caught in a single run and photo-electric control operation, the motor brake is to pull in the frequent separation of action in the conduct of, so that when the friction brake on each wheel does not pull a little trip in place or slightly biased, it is easy to bias the local end to the corresponding shaft friction wheel, and increase the electrical resistance of the work, and then slow down the speed of the folder causing the book. The continuous automatic operation, the motor brake on the friction wheel pull off after the separation of its location is fixed, not easy for grazing to the corresponding wheel brake, so no books on the folders sometimes slow pace of the situation. Given the characteristics of this failure, the author is the main motor brake preliminary judging problems more likely, therefore, and through careful observation, finally found the friction brake on the wheel separation in the gap pull a uniform phenomenon, locally minor grazing to the corresponding wheel axle, so that the motor shaft have a certain resistance. When a hand to touch the brakes, it felt very hot. In this regard, the author removed by the brake, the inside of the dirt clean, and re-adjust the friction wheel with the corresponding round of the gap, so that the pull of separation does not appear grazing situation, then, the book clip in a single run or photoelectric control operation, no longer the phenomenon does not appear to run slower, the fault has finally been completely eliminated, the machine quickly returned to normal state.
The fault of the excluded, to the author with an intimate knowledge and experience, machinery in the production process, a variety of complex fault may occur at any time, for the moment difficult to determine the reasons for the failure, electrical failure problems, as both may and like the situation of the phenomenon of mechanical failure, do not rush blindly for processing. Must be through careful observation and analysis, step by step, orderly and meticulous examination, and then solve the problem of the characteristics of a series of ideas, analysis and verification, to determine better to avoid mistakes caused by processing in the blindness, to achieve fast and accurate troubleshooting, restoration of normal production machines. I am a professional writer from China Furniture Manufacturer, which contains a great deal of information about prime time cigar , davidoff of geneva, welcome to visit!
Related Articles -
prime time cigar, davidoff of geneva,
|