If it is geothermal heating, laying solid wood flooring can do? Likely that most consumers do not think that shop, because of solid wood flooring is so easy to crack, then there is no way to overcome this weakness?
Currently on the market there is a Wood Snap geothermal heating floor. This flooring is easy to overcome a solid wood floor bagging, tile change, cracking, defects from the joint resolve of the shrinkage of wood floors due to wet up caused quality problems. It uses snaps two-man stretch contraction, and installation of expansion joints allow a certain amount of adjustment up wet shrinkage of wood flooring, solid wood flooring is easy to solve the bagging and easily from the joint problem. Is the use of air conduction, effectively solve the poor thermal conductivity of solid wood flooring, slow, big and so heat loss. Splicing between the floor and the floor do not have male and female wedge between the board and the board, snaps and snaps can create a good communication between the several channels.
This snap-in installation, floor, between the board and the board left 0.2 ~ 0.4mm gap, not only to solve the solid wood flooring installed in the sound produced is more important is to change the traditional wood-conductor transmission heat, humidity and method using air as the carrier for the convection heat, humidity and methods conducive to saving energy, reducing floor deformation. This snap-in floor during the installation process to avoid nails, glue-free, non-keel, reducing noise pollution in the installation process, and very simple, just a few minutes to take a few days to complete the floor of the original replacement.
Laminate Flooring should use a small size on the market today use more geothermal floor is laminate flooring and solid wood flooring, laminate flooring thickness mostly in the 7 ~ 8mm, it is easy to geothermal system heat conduction to the surface, and its surface Wear layers of metal oxides, the heat at the surface and evenly spread very fast. Imports to the European Enpr13329 standards of quality flooring, domestic flooring GB/T1802-2000 quality reach the national standard, can be adapted to geothermal heating floor installation technical requirements, passing a number of brands currently on the market have reached this standard. Lock-type floor better, because hook joint between the floor left a small gap, so difficult to take shape after expansion.
In order to increase the heat conductivity, the thickness of cushion material and the floor should not be too thick to heat the floor of the standard thickness of 6.5 ~ 8.5mm, laminate floor should be 6 ~ 8mm, three parquet is 8 ~ 9mm. Encourages consumers to use caution as far as possible for a small, preferably 200 × 40 × 10 makes up the square or chevron, its thermal deformation uniform. If you choose laminate flooring can be used Power Dekor, regal, macro-resistant, the European Code, Park Lane and other famous brands dedicated to heat the floor. The manufacturers of the substrate density demanding, the same thickness of the strength, permeability, and good heat dissipation, heat through special processing. If you choose solid wood flooring can choose to Efavirenz, Hofman, the time dedicated to other famous brands heat the floor.
Tips to install geothermal heating floor should strictly comply with procedures 1, installed 24 hours before gradually heated, the temperature must keep the ground clean and dry and the former to prevent cracking of the floor occurs due to excessive heat distortion.
2, the first time use or long-term use of geothermal heating is not turned on, it should first set to the lowest temperature, and then slowly heating up, the best Mei Xiaoshi suitable temperature is about 1 ?, wood flooring gradually adapt to warming temperatures. If heated too fast, wooden floors may cause excessive heat, resulting in distortion of crack instability changes affect the service life of wooden flooring.
3, in the geothermal heating wooden floor is not as fixed as decorative pieces or placement of furniture without legs, to prevent local cooling is not smooth, heat boring in wood floor and easy to produce uneven floor deformation due to heat. I am a professional editor from China Product, and my work is to promote a free online trade platform. http://www.himfr.com/ contain a great deal of information about three billy goats , vietnam lacquer welcome to visit!
Related Articles -
three billy goats, vietnam lacquer,
|
